Free Morse Code Translator

Morse Code Translator
Text to Morse and Back

Type text to get Morse code, or paste dots and dashes to decode them. Play the sound and copy the result. It runs in your browser.

What is a Morse code translator? A Morse code translator converts letters and numbers into patterns of short and long signals, written as dots and dashes, and converts them back. Used as a Morse code generator it turns text into dots and dashes, and used as a Morse code decoder it reads dots and dashes back into text. This one uses International Morse Code. Letters are separated by a space and words by a slash, so HELLO WORLD becomes .... . .-.. .-.. --- / .-- --- .-. .-.. -..

Result
0.0 s / 0.0 s

How to Translate Morse Code in 3 Steps

  1. Type your message in the box. For decoding, paste dots and dashes instead, with a space between letters and a slash between words.
  2. Read the result under the box. It updates as you type, and the label shows which direction was used.
  3. Press Copy Result to take it, or press Start to hear the signal while a timeline shows each dot and dash. Click the timeline to jump to any point. Press Download TXT to save the result as a text file, or Download WAV to save the sound as an audio file. Slide the speed control to slow it down while you learn.

How Morse Code Works

Every character is a pattern of short signals (dots) and long signals (dashes). Timing carries the structure. A dot is one unit long and a dash is three. The pause inside a letter is one unit, the pause between letters is three units, and the pause between words is seven. In writing, a space stands for the letter pause and a slash for the word pause.

The translator here uses International Morse Code, the form used in amateur radio. American Morse, the older telegraph version, uses different patterns for some letters and is not what this tool produces. The playback follows the usual speed convention, where one unit lasts 1200 divided by the speed in words per minute, in milliseconds. At the default 15 words per minute a dot lasts 80 milliseconds.

Common Phrases in Morse Code

These were made by this translator, so they match what you get when you type the same words.

PhraseMorse code
SOS... --- ...
HELLO.... . .-.. .-.. ---
HELP.... . .-.. .--.
I LOVE YOU.. / .-.. --- ...- . / -.-- --- ..-
GOOD MORNING--. --- --- -.. / -- --- .-. -. .. -. --.
THANK YOU- .... .- -. -.- / -.-- --- ..-
OK--- -.-
YES-.-- . ...
NO-. ---

Morse Code Chart: Letters, Numbers and Punctuation

This is the same table the translator uses, so every pattern below can be typed or decoded above.

Letters

A.-
B-...
C-.-.
D-..
E.
F..-.
G--.
H....
I..
J.---
K-.-
L.-..
M--
N-.
O---
P.--.
Q--.-
R.-.
S...
T-
U..-
V...-
W.--
X-..-
Y-.--
Z--..

Digits

0-----
1.----
2..---
3...--
4....-
5.....
6-....
7--...
8---..
9----.

Punctuation in the ITU list

..-.-.-
,--..--
?..--..
'.----.
/-..-.
(-.--.
)-.--.-
:---...
=-...-
--....-
".-..-.
@.--.-.

Common extra marks

These six marks are not in the ITU list. They are widely used conventions, so a receiver may not know them.

!-.-.--
&.-...
;-.-.-.
+.-.-.
_..--.-
$...-..-

Sending Morse Code With a Flashlight

Light works the same way as sound. A short flash is a dot and a long flash is a dash, and the long flash lasts about three times as long as the short one. Use the timeline above as a guide: each block is one signal, and the gaps between blocks are the pauses. Read the pattern from the result box, then flash it with a torch or a phone light, keeping the pauses even. A distress call is a different matter. Contact local emergency services first and treat a flashlight signal as a backup.

Morse Code Phrases and Names

If you want ready-made messages, the guide to Morse code phrases, from SOS to I love you lists 38 common phrases, 10 names, the digits and a bracelet bead count, all made with the same table as this translator.

Writing Morse Code by Hand

If you write Morse on paper or in a message, keep the spacing consistent. A single space between letters and a slash between words is the easiest convention to read back. Without a clear word break, a long run of letters can be decoded more than one way, because some patterns are the start of longer ones. Typing the dot as a full stop and the dash as a hyphen avoids the look-alike characters that cause most copy and paste mistakes.

Morse Code Translator FAQ

Type or paste your text into the box. The translator shows the Morse code underneath as you type, with a space between letters and a slash between words. Press Copy to take the result, or Play to hear it.
Paste dots and dashes into the box, with a space between letters and a slash between words. The translator sees that the input is Morse and decodes it automatically. You can also switch the mode with the buttons.
S is three dots, O is three dashes and S is three dots again, so SOS is ... --- ... in this translator. As a distress signal it is sent as one run with no gaps between the letters, which gives ...---...
In International Morse Code a dash lasts three times as long as a dot. The gap inside a letter is one dot long, the gap between letters is three dots and the gap between words is seven dots.
It handles the letters A to Z, the digits 0 to 9 and the punctuation in the chart above. Accented letters are reduced to their plain letter, so é becomes E. Characters it still does not know, such as emoji, are skipped and listed under the result so you can see what was left out.
Yes, both. Press Download TXT to save the Morse code as a text file. For the sound, translate your text to Morse, set the speed, and press Download WAV. The file is made in your browser as a 600 Hz tone and saved as a WAV audio file, which plays in any normal audio player. Messages longer than five minutes of audio are not downloaded.
Yes, both. Type text to generate Morse code, or paste dots and dashes to decode them back into text. The tool detects which one you need, and you can switch the direction with the buttons.
Translate your message, then flash each dot as a short flash and each dash as a long flash that lasts about three times as long. Pause for about three short flashes between letters and about seven between words. The timeline on this page shows the same rhythm.
It is free and needs no account. The translation runs in your browser, so the text you type stays on your device.
Yes. The decoder accepts the plain dot and hyphen as well as the typographic characters some sites use, such as the middle dot and the en dash. Separate letters with a space and words with a slash.